如題，怎麼才能解決vertical retrace在系統裏運行不了的問題呢
以下是我運行的程序
clear all;
HideCursor;
window=Screen('OpenWindow',0);
KbWait;
Screen('CloseAll');
出現的報錯內容
PTB-INFO: This is Psychtoolbox-3 for Microsoft Windows, under Matlab 64-Bit (Version 3.0.14 - Build date: Oct 3 2017).
PTB-INFO: Support status on this operating system release: Windows version 10.0 supported and tested to some limited degree.
PTB-INFO: Type 'PsychtoolboxVersion' for more detailed version information.
PTB-INFO: Most parts of the Psychtoolbox distribution are licensed to you under terms of the MIT License, with
PTB-INFO: some restrictions. See file 'License.txt' in the Psychtoolbox root folder for the exact licensing conditions.
PTB-INFO: The detected endline of the vertical blank interval is equal or lower than the startline. This indicates
PTB-INFO: that i couldn't detect the duration of the vertical blank interval and won't be able to correct timestamps
PTB-INFO: for it. This will introduce a very small and constant offset (typically << 1 msec). Read 'help BeampositionQueries'
PTB-INFO: for how to correct this, should you really require that last few microseconds of precision.
PTB-INFO: Btw. this can also mean that your systems beamposition queries are slightly broken. It may help timing precision to
PTB-INFO: enable the beamposition workaround, as explained in 'help ConserveVRAMSettings', section 'kPsychUseBeampositionQueryWorkaround'.
PTB-WARNING: Couldn't even collect one single valid flip interval sample! Sanity range checks failed!
PTB-WARNING: Could be a system bug, or a temporary timing problem. Retrying the procedure might help if
PTB-WARNING: the latter is the culprit.
WARNING: VBL Calibration run No. 1 failed. Retrying...
PTB-WARNING: Couldn't even collect one single valid flip interval sample! Sanity range checks failed!
PTB-WARNING: Could be a system bug, or a temporary timing problem. Retrying the procedure might help if
PTB-WARNING: the latter is the culprit.
WARNING: VBL Calibration run No. 2 failed. Retrying...
WARNING: Will enable VBL busywait-workaround before trying final VBL Calibration run No. 3.
WARNING: This will hopefully work-around graphics driver bugs of the GPU sync-to-retrace mechanism. Cross your fingers!
PTB-INFO: OpenGL-Renderer is NVIDIA Corporation :: GeForce 840M/PCIe/SSE2 :: 4.5.0 NVIDIA 369.09
PTB-INFO: VBL startline = 768 , VBL Endline = 768
PTB-INFO: Measured monitor refresh interval from beamposition = 16.650105 ms [60.059680 Hz].
PTB-INFO: Will use beamposition query for accurate Flip time stamping.
PTB-INFO: Measured monitor refresh interval from VBLsync = 16.670121 ms [59.987568 Hz]. (50 valid samples taken, stddev=0.401861 ms.)
PTB-INFO: Reported monitor refresh interval from operating system = 16.666667 ms [60.000000 Hz].
PTB-INFO: Small deviations between reported values are normal and no reason to worry.
PTB-INFO: ==============================================================================================================================
PTB-INFO: WINDOWS DWM DESKTOP COMPOSITOR IS ACTIVE. On this Windows-10 or later system, Psychtoolbox can no longer reliably detect if
PTB-INFO: this will cause trouble for timing and integrity of visual stimuli or not. You might be just fine, or you could be in trouble.
PTB-INFO: Use external measurement equipment and independent procedures to verify reliability of timing if you care about proper timing.
PTB-INFO: ==============================================================================================================================
WARNING: Couldn't compute a reliable estimate of monitor refresh interval! Trouble with VBL syncing?!?
----- ! PTB - ERROR: SYNCHRONIZATION FAILURE ! ----
One or more internal checks (see Warnings above) indicate that synchronization
of Psychtoolbox to the vertical retrace (VBL) is not working on your setup.
This will seriously impair proper stimulus presentation and stimulus presentation timing!
Please read 'help SyncTrouble' for information about how to solve or work-around the problem.
You can force Psychtoolbox to continue, despite the severe problems, by adding the command
Screen('Preference', 'SkipSyncTests', 1); at the top of your script, if you really know what you are doing.